|You are here: RoboFlag Main Page > Course Resources > Technical Information > Datasheets|
The following datasheets are stored locally, with a link to where they were found on the web. If the datasheet detailed below seems out of date, check for a new version!
MIT HandyBoard - The unified hard-copy Handy Board technical
document. Includes: explanation of Handy Board ports and connectors, quick
start instructions, 6811 downloader explanation, freeware Interactive C
manual, motor and sensor wiring diagrams, full schematics, printed circuit
board artwork (1.5x scale), vendor and licensing information.
Texas Instruments SN754410 Half H-Bridge - Quadruple Half-H
Driver: provides bidirectional drive currents up to 1A at voltages from
4.5V to 36V. The device is designed to drive inductive loads such as
relays, solenoids, dc and bipolar stepping motors, as well as other
high-current/high-voltage loads in positive-supply applications.
SGS Thompson L293D Half H-Bridge - a monolithic integrated high
voltage, high current four channel driver designed to accept standard DTL
or TTL logic levels and drive inductive loads (such as relays solenoides,
DC and stepping motors) and switching power transistors. (600mA max)
SGS Thompson L298 Full H-Bridge - an integrated monolithic
circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high
voltage, high current dual full-bridge driver designed to accept standard
TTL logic levels and drive inductive loads such as relays, solenoids, DC
and stepping motors. (4A max)
Microchip PIC16F84A Microprocessor - FLASH/EEPROM
microcontroller with an easy-to-learn instruction set (only 35 single word
instructions). PIC16F84A contains 1024x14 word of FLASH program memory,
64 data memory bytes, and 68 bytes of user RAM. The device also features
an 8-bit timer/counter with 8-bit programmable prescaler, Watchdog timer
with its own on-chip RC oscillator for reliable operation, Power-On-Reset
(POR) Power-up Timer (PWRT), Oscillator Start-up timer (OST) and a maximum
speed of 20MHz.
RALTRON 20MHz Crystal Oscillator - 14-pin DIP package (there are
only 4 actual pins, but the device is 7-pins long) for use with the PIC as
a high-speed clock source. 20.000MHz+-100ppm.
ECS Ceramic Resonator (with caps) - this 3-pin package includes
built-in load capacitors with the ceramic resonator. Used as a clock
source for the PIC. 20MHZ+-0.5%.
MING TX-01 Encoder Motherboard - The TX-01 is a encoder
motherboard which is designed to be incorporated with the MING TX-99
transmission boards in order to provide a complete encoder/transmitter
MING TX-99-V3 RF Transmitter - The TX-99 v3.0 is a 300 MHz
transmitter board which is designed to be incorporated with our TX-01
mothterboards in order to provide a complete encoder/transmitter
MING RE-01 Decoder Motherboard - decoder motherboard which is
designed to be incorporated with the MING RE-99 receiver boards in order
to provide a complete receiver/decoder solution.
MING RE-99-V3 RF Receiver - The RE-99 v3.0A is a 300 MHz
receiver board which is to be used with the MING RE-01 decoding
motherboard if you will not be adding your own decoding microprocessor or
chipset. The combination of both RE-99 v3.0A and the RE-01 will provide a
complete receiver/decoder solution.
Burr-Brown OPT101P Photodiode with transimpedance amplifier -
The OPT101P is the perfect device to detect the flashing visible flag beacon. The sensor will return
an analog signal that can be sampled for the presence of the beacon. A
number of operating suggestions are available here.
Holtek HT12A Encoder - a CMOS LSI for remote control system
applications. Capable of encoding information which consists of N address
bits and 12-N data bits. Can be used for infrared, RF, or even on a fixed
line with a shared bus. We're using it for our infrared robot beacon.
Holtek HT12D Decoder - a CMOS LSI for remote control system
applications. Paired with Holtek 12A Encoders, these devices receive
serial address and data from an RF or IR transmission medium. We're using
it for our infrared robot beacon.
Panasonic PNA4612M Infrared Detection Module - a bipolar
integrated circuit with photodetection function. This device demodulates
an infrared signal (removing a 38kHz carrier). We're using it for our infrared robot beacon.
Lumex OED-EL-1L2 Infrared LED - this T-5mm leaded LED is made
with clear epoxy and features a 60-degree beam angle. The LED can pass
100mA continuous current, has a 1.7V Vf, and has a wavelength of 940nm.
We're using it for our infrared robot